As you may have read in other reviews, the sticks are excellent in both quality/workmanship and functionality. However, they do not fit M9 gimbals out of the box, due to lower portion being too thin. Here is how I have modded mine to fit, if you don't mind loosing some of the bottom conical part. Cut off the bottom half of conical section, leaving only 4.5-5mm (see my last pic in reference to original stick). Do not try and leave it any longer as it will tear the sides while you drill into it, and end up with it even shorter. After cutting, use a 7/32 drill bit (3/16 is too small) to drill out the conical section to allow it to fit over the stick. A tip here is to use a 4mm bolt through the rocker to allow you to hold it and also to stop the drill bit from going into the threaded portion (only screw the bolt up to the end of the thread). I've also added a bit of black heat-shrink to make up for the cut off part and think it looks really slick.

As you may have read in other reviews, the sticks are excellent in both quality/workmanship and functionality. However, they do not fit M9 gimbals out of the box, due to lower portion being too thin. Here is how I have modded mine to fit, if you don't mind loosing some of the bottom conical part. Cut off the bottom half of conical section, leaving only 4.5-5mm (see my last pic in reference to original stick). Do not try and leave it any longer as it will tear the sides while you drill into it, and end up with it even shorter. After cutting, use a 7/32 drill bit (3/16 is too small) to drill out the conical section to allow it to fit over the stick. A tip here is to use a 4mm bolt through the rocker to allow you to hold it and also to stop the drill bit from going into the threaded portion (only screw the bolt up to the end of the thread). I've also added a bit of black heat-shrink to make up for the cut off part and think it looks really slick.

As you may have read in other reviews, the sticks are excellent in both quality/workmanship and functionality. However, they do not fit M9 gimbals out of the box, due to lower portion being too thin. Here is how I have modded mine to fit, if you don't mind loosing some of the bottom conical part. Cut off the bottom half of conical section, leaving only 4.5-5mm (see my last pic in reference to original stick). Do not try and leave it any longer as it will tear the sides while you drill into it, and end up with it even shorter. After cutting, use a 7/32 drill bit (3/16 is too small) to drill out the conical section to allow it to fit over the stick. A tip here is to use a 4mm bolt through the rocker to allow you to hold it and also to stop the drill bit from going into the threaded portion (only screw the bolt up to the end of the thread). I've also added a bit of black heat-shrink to make up for the cut off part and think it looks really slick.

Nur die Spitze des X9D Plus SE 2019 - Sticks kann ausgetauscht werden. Der Standard-Stick wurde für Daumenschalen entwickelt und es war schwierig für mich, den Pincher zu bedienen, so dass es einfacher war, den Stick zu kontrollieren, wenn ich ihn ersetzt habe. (Es ist ein persönlicher Eindruck.)

X9D Plus SE 2019 のスティックの先端だけを交換して使えます。標準のスティックはサムナー向けの形状でピンチャーの私には操作しにくかったので、交換したら繊細なコントロールがやりやすくなりました。（個人的な感想です。）

Nur die Spitze des X9D Plus SE 2019 - Sticks kann ausgetauscht werden. Der Standard-Stick wurde für Daumenschalen entwickelt und es war schwierig für mich, den Pincher zu bedienen, so dass es einfacher war, den Stick zu kontrollieren, wenn ich ihn ersetzt habe. (Es ist ein persönlicher Eindruck.)